6SE6440-2UD21-1AA1 MANUAL PDF

6SEUDAA1. –. –. – .. Instruction Manual for details. LC filter and sinusoidal .. General installation instructions. Availability of the. (n. di ordinazione 6SE . You will find the Operating Instructions on the Docu CD delivered with your inverter. If and Notes contained in these manuals. MICROMASTER kW – kW. Operating Instructions. Issue 12/ User Documentation. 6SEAWBP0.

Author: Akinokora Kagagar
Country: Laos
Language: English (Spanish)
Genre: Photos
Published (Last): 22 June 2016
Pages: 36
PDF File Size: 11.31 Mb
ePub File Size: 11.51 Mb
ISBN: 912-9-64425-766-7
Downloads: 72213
Price: Free* [*Free Regsitration Required]
Uploader: Dar

Page 29 – Fig. Unscrew the bolts in the iron brackets on the transport pallet and lift the inverter off the pallet. Page Power and motor connections When starting the motor data identification routine, the rotor can move into a preferred position. This means that it is not possible to save a parameter set on the BOP. Page 75 entry according to the rating plate Fig.

This will be shown in manua, following example using the fixed frequency P and digital input 1 refer to Fig. Quick Amnual Refer to the parameter list for additional setting possibilities. Motion control, frequency inverter dc-ac compact plus type pages.

Siemens MICROMASTER 440 Operating Instructions Manual Page 10

Page 39 – Fig. Page of Go.

This connection is normally used to ground the motor. Load Torque Monitoring This avoids erroneous alarms which could be caused by manul transient states refer to Fig.

Siemens MICROMASTER Quick Start Manual (Page 15 of 68)

NOTE If the drive inverter fan fails, this would be indirectly detected by the measurement of the heatsink temperature. Yes Group Active QuickComm.

  LOS TARAHUMARAS ANTONIN ARTAUD PDF

Increasing the level of braking energy which can be absorbed A list of the parameters, which are calculated, depending on the setting of P, are included in the parameter list.

Page NOTE If the drive inverter fan fails, this would be indirectly detected by the measurement of the heatsink temperature.

Page 42 Page 43 – Fig. The inverter pulses are inhibited after the braking time has expired. Frequently manuql states including the parameter number and bit are shown in the following Table refer to Table DC link voltage limit r refer to Fig.

Page 46 Vector control Page 79 – Fig. Positioning Down Ramp In order to carry-out the residual distance calculation on the load side, the mechanical arrangement of the axis gearbox ratio, linear or rotary axis must be appropriately parameterized refer to Fig. If problems occur during the identification run, e. Page The chopper of the braking module switches the resistor with a mark- space ratio corresponding to the regenerative power to be dissipated.

Page Motor Load Fig. Page 0, it is possible that the drive is accelerated as a result of the search current! This therefore eliminates the speed reduction, caused by the load, by boosting increasing the drive inverter output frequency refer s6e6440-2ud21-1aa1 Fig. Use for intended purpose only The equipment may be used only for the application stated in the manual and only in conjunction with 6se6440-2ud21-1aaa1 and components recommended and authorized by Siemens. The motor parameters have been calculated and it is now possible to return to the additional parameterization in the Section “Adaptation to 6se64400-2ud21-1aa1 application”.

  ENTSPANNUNGSGESCHICHTEN ERWACHSENE PDF

This is more significant for larger motors. As far manuak the ability to visualize the parameters is concerned, the group assignment of the individual parameters must be taken into account.

Page 38 – Fig. Table Compliance Table Unfiltered units, all voltages and powers. The connection of 6se6440-2ud1-1aa1, motor and 6se644-02ud21-1aa1 cables to the inverter must be carried out as shown in Fig. Depending on external circumstances, the supplementary setpoint can be dynamically disconnected or switched-in to the summation point refer to Fig.

Page 47 The drive unit may not be used as ‘Emergency switching-off device’ refer to EN9. The drive unit may not be used as ‘Emergency switching-off device’ refer to EN9. Series Commissioning This means that it is possible to transfer the parameter set from drive inverter A to drive inverter 6se4640-2ud21-1aa1 which, for identical applications e.

Page 22 The connection of power, motor and control cables to the inverter must be carried out as shown in Fig. The following data sets apply: